Sale!

get-the-look-at-a-lower-cost-with-our-selection-of-cisco-sm-x-1t3-e3-packet-over-t3-e3-service-module-for-cisco-integrated-services-routers-cisco-outlet-sale_0.jpg

Cisco SM-X-1T3/E3 Packet-over-T3/E3 Service Module for Cisco Integrated Services Routers Cisco Outlet Sale

Original price was: $ 11.298.Current price is: $ 2.825.

SKU: us_6760489746535 Category: All Products Tags: All Products, Cisco, Integrated Services Router, Switches/Routers

Description
shopping

Enable your Cisco integrated service router to quickly switch between T3 and E3 WAN modes with the SM-X-1T3/E3 Packet-over-T3/E3 Service Module for Cisco Integrated Services Routers from Cisco. Designed for use with Cisco 2900, 3900, and 4000 Series integrated service routers, the SM-X-1T3/E3 service module lets you switch between T3 and E3 applications by executing a single Cisco IOS Software command.

This one-port service module comes equipped with two 75 Ohm BNC coaxial connectors, one for transmitting and another for receiving. Full-duplex T3 and E3 communication is supported. An integrated line interface unit (LIU) allows T3 or E3 lines to be directly terminated on your compatible Cisco router.

T3/E3 Line Termination

The increased demand for bandwidth over the WAN and more attractive pricing of T3/E3 links by service providers has led to steady growth in T3/E3 deployments around the world. The T3/E3 module eliminates the need for an external data service unit (DSU), reduces provisioning costs, and provides highly manageable T3/E3 line termination. The module provides an integrated line interface unit (LIU) DSU that allows T3 or E3 lines to be directly terminated on a Cisco router, eliminating the need for external DSU equipment, simplifying the T3/E3 line management, reducing provisioning cost, and freeing valuable rack space.

Interoperability with Third-Party DSU Vendors

The T3/E3 module supports the proprietary subrate and scrambling features of T3 DSU vendors such as Digital Link, Larscom, and ADC Kentrox. Subrate support in the module helps to maximize the utility of these products in service provider environments. By simultaneously supporting interoperability with a wide range of third-party DSU vendors, this module offers the flexibility to support installed equipment without locking customers into a proprietary solution.

Compatibility

The Cisco T3/E3 Service Module provides direct connectivity to a T3 line for full-duplex communications at the T3 rate of 44.736 MHz and full-duplex E3 communications at 34.368 MHz. Each T3 or E3 port consists of a pair of 75 Ohm BNC coaxial connectors (type RG-59), one for transmitting data and one for receiving data, along with six LED indicators for line status. The T3/E3 module is supported in most Cisco IOS Software feature sets, and there are no additional memory requirements.

General Features

One-port T3 with DSU or E3 with DSU module

T3/E3-specific features for monitoring, bit error rate tester (BERT), MIBs, alarms, and more

Ability to independently or simultaneously enable scrambling and subrate in each DSU mode

Support for the following DSU vendors’ algorithms: Digital Link, Kentrox, Larscom, Verilink, and Adtran

Support for the serial encapsulation protocols: Frame Relay, Point-to-Point Protocol (PPP), and High-Level Data Link Control (HDLC)

16-bit cyclic redundancy check (CRC)

Management Features

Line and payload loopback capabilities

DS-3 remote-line loopback through Far-End Alarm and Control (FEAC) codes per American National Standards Institute (ANSI) T1.107a

Response to embedded loopback commands

Insertion of loopback commands into transmitted signal

Programmable pseudorandom pattern up to 32 bits long, including 223, 220, 215, 1s, 0s, and alt-0-1

32-bit error count and bit-count registers

Alarm detection-Alarm indication signal (AIS), remote alarm, far-end block error (FEBE), and out of frame (OOF)

Onboard processor for Maintenance Data Link (MDL)

T3/E3 Applications and Positioning

The Cisco T3/E3 Service Module provides the performance requirements to deploy advanced voice, video, and data applications over the WAN and supports key Cisco IOS Software features and services such as quality of service (QoS), Network-Based Application Recognition (NBAR), IP Security (IPsec), Firewall, intrusion detection system (IDS), Network Address Translation (NAT), and NetFlow.

Fast Shipping and Professional Packing

Through our long-term relationship with UPS, FedEx, DHL and a variety of other world-class carriers, we are able to offer a variety of shipping options. Our warehouse staff is extremely skilled and will package your products according to our exact and precise specifications. Your items will undergo an extensive inspection and will be properly secured before they are delivered. Each day, we ship to thousands of customers across different countries. Our determination to be the biggest online retailer around the globe is evident by this. We have distribution centers and warehouses located in Europe and in the USA.

Orders with more than one item are assigned processing times in accordance with the item.

We will thoroughly inspect all products before they are shipped. Today, the majority orders will be sent within 48 hours. Expected delivery time is between 3-7 days.

Returns

We are not able to control the inventory in our warehouse and factory. Stock levels can fluctuate at any moment. Please be aware that it's possible that your order will be out of stock after you have placed the order.

The policy is 30 days. If 30 days have passed in the past since you purchased and we are unable to offer an exchange or refund.

For your item to be eligible for return the item must not be opened and in the condition you received it. The item must be in its original packaging.

Cisco SM-X-1T3/E3 Packet-over-T3/E3 Service Module for Cisco Integrated Services Routers Cisco Outlet Sale

Related products

Login